Audio and music

Violin Tuner

Choose one string and bow or pluck it evenly. Adjust with small movements, especially near the higher E string.

Detected note—Waiting for microphone
TargetG3196.0 Hz
Flat—Sharp

Play one note at a time in a quiet room. A4 reference: 440 Hz.

Keep your other strings quiet. This tuner uses A4 = 440 Hz.

Understanding the result

The online violin tuner uses real-time microphone analysis to evaluate open violin strings against standard G3 D4 A4 E5 tuning in perfect fifths at concert pitch (A4 = 440 Hz). Real-time cents metrics and frequency readouts guide both pegbox friction peg and fine-tuner adjustments.

How to use this tool

  1. Choose G3, D4, A4 or E5.
  2. Play one string steadily.
  3. Bring the cents reading close to zero.

Standard Violin Tuning: G3 D4 A4 E5 in Perfect Fifths

The violin is tuned in ascending perfect fifths: 4th String (G3 ≈ 196.00 Hz), 3rd String (D4 ≈ 293.66 Hz), 2nd String (A4 = 440.00 Hz), and 1st String (high E5 ≈ 659.25 Hz). Numbering runs from the thinnest, highest string (E string on the right) to the thickest, lowest string (G string on the left). Standard orchestral tuning establishes the A4 reference first, followed by D4, G3, and E5.

Fine Tuners vs. Pegbox Friction Pegs

Because the steel E string is under immense tension with minimal stretch, almost all violins feature a fine tuner on the E string tailpiece. Many student instruments have fine tuners on all four strings. Use the wooden friction pegs in the pegbox for major tuning changes, pushing inward firmly while turning clockwise. Use the fine tuners for gentle micro-adjustments within ±30 cents.

Bowing (Arco) Technique for Clean Tuner Detection

Draw a smooth, steady, medium-speed bow stroke halfway between the bridge and fingerboard. Keep the bow perpendicular to the string and avoid excessive arm weight that distorts pitch. A clean mezzo-forte tone provides the tuner with a continuous, stable fundamental frequency.

Pizzicato Tuning Option for Quiet Environments

If you are tuning without a bow, pluck the string firmly with the pad of your index finger over the end of the fingerboard. Let the note sustain cleanly without resting your finger back onto the string immediately.

Checking Harmonic Fifths and Ringing Overtones

After tuning each string individually, classical players bow adjacent pairs (A+D, D+G, E+A) to verify that the intervals ring without pulsing phase beats. Our tuner helps you establish accurate baseline reference pitches across all four strings.

Troubleshooting

  • Peg slips and string goes completely loose: Wooden violin pegs rely on friction. Push the peg inward toward the pegbox while turning clockwise to lock the taper into the hole.
  • Fine tuner screw is screwed all the way down: Loosen the fine tuner screw almost to the top, use the friction peg to bring the string back to approximate pitch, then use the fine tuner again.
  • High E string detected as E6: Pluck or bow with a softer touch and ensure the instrument is 8–12 inches from your microphone.
  • Needle fluctuates while bowing: Maintain a steady bow stroke without stopping or changing pressure mid-bow.

Browser and device limitations

Monophonic Web Audio pitch detection tracks one note at a time; double-stops cannot be analyzed simultaneously.

RELATED TOOLS
All tools

Common questions

Can I tune by plucking?

Yes. A clear plucked note is often easier for the microphone to identify.

What if the tuner shows a nearby string?

Check the selected target and play only that string.

Should I always tune the A string first on violin?

Yes. In orchestras and ensembles, the oboe or concertmaster sounds A4 (440 Hz), and all players tune their A string first before tuning the lower fifths.

LanguageEnglishहिन्दी